Overview
The model 5182 is a current-to-voltage preamplifier of low noise and low input impedance designed to amplify the extremely low currents encountered in such areas as photometry and semiconductor research. It has four standard sensitivity settings but in addition includes a special low-noise mode on the highest gain position for even better low current measurement capability. The unit features two outputs, allowing both the AC and DC components of the input signal to be independently monitored, so that, for example, in a PMT application the bias current can be measured separately from the signal current.
It can be powered from its own internally housed (alkaline) batteries, an external low voltage supply (±15 V or ±18 V) or from the model PS0108 remote line power supply(optional extra). This preamplifier can also be powered from most of our range of lockin amplifiers.
The model 5182 is ideally suited to amplifying signals from current sources such as electron multipliers, ion collectors, photomultipliers and photodiodes.
- Low input impedance
- Low noise
- Single-ended virtual ground innput
- Adjustable snesitivity
- Bias current monitor (DC) and signal (AC) outputs
- DC to 1 MHz frequency response
- Battery or external DC power
- Photodiode amplification
- Photomultiplier amplification
- Ion collector amplification
- Electron multiplier amplification
Specifications
General
DC coupled current to voltage amplifier with adjustable sensitivity and a maximum frequency response extending from DC to 1 MHz. Single-ended virtual ground input and single-ended DC and AC coupled outputs via BNC connectors
Battery powered from internal alkaline batteries or external DC power supply.
Inputs | |
Modes | Single-ended virtual ground |
Coupling | DC |
Sensitivity | Switch selectable (5 settings) |
AC Output | 10-5, 108, 107, 108, 108 low noise A/V |
DC Output | 10-3, 104, 106, 107, 108 A/V |
Accuracy | ±2% |
Stability | ±300 ppm/* C |
Impedance | see Figure 1 |
Max input w/o damage | ±15 V DC or 10 V rms. AC @ 50 Hz |
Noise | see Table 1 |
Frequency Response (AC Output) |
lower limit 0.5 Hz upper limit depends on sensitivity setting, see Figure 2 |
Max DC current at input | see Table 1 |
Outputs | |
AC Output Impedance Max voltage swing Slow rate |
450 Ω >10 V pk-pk > 22 V/µs |
DC Output Impedance Max voltage swing Polarity |
10 kΩ >±9 V Current flowing into the input produces positive output voltage |
Power Internal |
Four 9 V alkaline batteries provide approximately 15 hours of use |
External a) b) |
±15 V or ±18 V DC @ 25 mA |
Dimensions (excluding connectors) |
8.25" wide x 11" deep x 3.5" high (210 mm wide x 279 mm deep x 89 mm high) |
Weight | 5.3 lbs. (2.4 kg) excluding optional power supply |
… [Trackback]
[…] Find More Information here to that Topic: ino.com.vn/khac-do-luong-kiem-tra/signal-recovery-current-preamplifier-model5182/ […]
… [Trackback]
[…] Read More Info here to that Topic: ino.com.vn/khac-do-luong-kiem-tra/signal-recovery-current-preamplifier-model5182/ […]
… [Trackback]
[…] There you will find 66859 more Information to that Topic: ino.com.vn/khac-do-luong-kiem-tra/signal-recovery-current-preamplifier-model5182/ […]
… [Trackback]
[…] Read More on that Topic: ino.com.vn/khac-do-luong-kiem-tra/signal-recovery-current-preamplifier-model5182/ […]
… [Trackback]
[…] Read More on on that Topic: ino.com.vn/khac-do-luong-kiem-tra/signal-recovery-current-preamplifier-model5182/ […]
… [Trackback]
[…] Find More Info here to that Topic: ino.com.vn/khac-do-luong-kiem-tra/signal-recovery-current-preamplifier-model5182/ […]